Files
inkscape.calibrationDecoupe…/board_photo_markers.inx
T
2026-09-27 11:37:02 +02:00

90 lines
5.1 KiB
XML

<?xml version="1.0" encoding="UTF-8"?>
<!--
Textes source en anglais, traduits par le catalogue « board_photo »
(commun aux entrées de menu). Après toute modification d'un
texte : python i18n.py, puis compléter po/fr.po et relancer.
Les réglages de l'onglet « Work area » doivent rester identiques à ceux
de board_photo_import.inx (mêmes noms, mêmes défauts).
-->
<inkscape-extension translationdomain="board_photo"
xmlns="http://www.inkscape.org/namespace/inkscape/extension">
<name>Board photo: print calibration markers</name>
<id>fr.alexp.board_photo.markers</id>
<param name="tab" type="notebook">
<page name="work_area" gui-text="Work area">
<param name="mode" type="optiongroup" appearance="combo" gui-text="Output:">
<option value="bed">Markers to engrave on the bed</option>
<option value="sheet">A4 sheet to print (markers to cut out)</option>
<option value="guides">Placement guides to engrave on the bed (for printed markers)</option>
</param>
<separator/>
<label appearance="header">Laser work area (mm)</label>
<param name="work_width" type="float" precision="1" min="10" max="5000"
gui-text="Width (mm):">400.0</param>
<param name="work_height" type="float" precision="1" min="10" max="5000"
gui-text="Height (mm):">400.0</param>
<param name="set_page" type="bool"
gui-text="Set the page to the work area size">true</param>
<separator/>
<label appearance="header">Calibration markers, inside or around the work area (laser origin at the bottom left)</label>
<param name="origin_x" type="float" precision="2" min="-1000" max="5000"
gui-text="Origin marker centre X (mm):"
gui-description="Distance from the laser origin to the centre of the two-dot marker, along X; negative when the markers are around the work area (left of the origin)">30.0</param>
<param name="origin_y" type="float" precision="2" min="-1000" max="5000"
gui-text="Origin marker centre Y (mm):"
gui-description="Distance from the laser origin to the centre of the two-dot marker, along Y (upwards); negative when the markers are around the work area (below the origin)">30.0</param>
<param name="spacing_x" type="float" precision="2" min="1" max="5000"
gui-text="Spacing between markers X (mm):">340.0</param>
<param name="spacing_y" type="float" precision="2" min="1" max="5000"
gui-text="Spacing between markers Y (mm):">340.0</param>
<param name="marker_size" type="float" precision="1" min="5" max="200"
gui-text="Marker size (mm):">20.0</param>
</page>
<page name="print" gui-text="Printed sheet">
<label xml:space="preserve">Print the sheet at actual size (100 %,
no "fit to page"), preferably from a PDF
(File > Save a Copy > PDF). Then measure
both 100 mm bars.
Only if the printer still shrinks the sheet,
enter the measured lengths below: the sheet
is enlarged to compensate. Print it again
and check that the bars now measure 100 mm.</label>
<param name="print_x" type="float" precision="1" min="80" max="120"
gui-text="Measured length of the horizontal bar (mm):">100.0</param>
<param name="print_y" type="float" precision="1" min="80" max="120"
gui-text="Measured length of the vertical bar (mm):">100.0</param>
</page>
<page name="help" gui-text="Help">
<!-- Schéma généré par docs/schema_parametres.py, en anglais :
Inkscape ne traduit pas le chemin d'une image. -->
<image width="675" height="521">images/parameters_en.png</image>
<separator/>
<!-- Un paragraphe par ligne : Inkscape le replie à la largeur de
l'onglet ; des retours à la ligne forcés le laisseraient étroit. -->
<label xml:space="preserve">Engraved markers: engrave them once, filled, on light plates fixed to the bed, keeping a light area of twice the marker size around each one.
Printed markers:
1. "A4 sheet": print at 100 % (no fit to page), check the 100 mm bar, cut out the 4 pieces along the dashed lines.
2. "Placement guides": engrave them lightly on the bed (thin red lines).
3. Stick each piece inside its guide, the ticks of the piece on the cross.
The markers must stay in place: every photo is scaled from them. The marker with two dots is the origin marker, at the bottom left (laser origin). Use the same settings in "Board photo: import and calibrate".</label>
</page>
</param>
<effect needs-live-preview="false">
<object-type>all</object-type>
<effects-menu>
<submenu name="AlexDesign"/>
</effects-menu>
</effect>
<script>
<command location="inx" interpreter="python">board_photo_markers.py</command>
</script>
</inkscape-extension>