# Modele de traduction de l'extension Inkscape « Board photo ». # Genere par i18n.py ; ne modifier que les msgstr. msgid "" msgstr "" "Project-Id-Version: board_photo\n" "MIME-Version: 1.0\n" "Content-Type: text/plain; charset=UTF-8\n" "Content-Transfer-Encoding: 8bit\n" #: board_photo_import.inx msgid "Board photo: import and calibrate" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Work area" msgstr "" #: board_photo_import.inx msgid "Honeycomb = laser work area (mm)" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Width (mm):" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Height (mm):" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Set the page to the work area size" msgstr "" #: board_photo_import.inx board_photo_markers.py msgid "Calibration markers" msgstr "" #: board_photo_import.inx msgid "Marker position:" msgstr "" #: board_photo_import.inx msgid "Around the honeycomb: the inner corner of each paper piece touches a corner of the honeycomb" msgstr "" #: board_photo_import.inx msgid "Custom: centre of the origin marker and spacing below" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Marker size (mm):" msgstr "" #: board_photo_import.inx msgid "Side of the black square; the paper piece is twice as large" msgstr "" #: board_photo_import.inx msgid "Around the honeycomb, everything is deduced: the bottom left corner of the honeycomb is the laser origin (bottom left of the page), and the spacing is the honeycomb size plus twice the marker size. The values below are only used for a custom position." msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Origin marker centre X (mm):" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Distance from the laser origin to the centre of the two-dot marker, along X; negative when the markers are around the work area (left of the origin)" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Origin marker centre Y (mm):" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Distance from the laser origin to the centre of the two-dot marker, along Y (upwards); negative when the markers are around the work area (below the origin)" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Spacing between markers X (mm):" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Spacing between markers Y (mm):" msgstr "" #: board_photo_import.inx msgid "Photo" msgstr "" #: board_photo_import.inx msgid "Photo source:" msgstr "" #: board_photo_import.inx msgid "Photo file" msgstr "" #: board_photo_import.inx msgid "Remote camera (capture server)" msgstr "" #: board_photo_import.inx msgid "Photo of the board:" msgstr "" #: board_photo_import.inx msgid "Photo taken from above, showing the 4 markers" msgstr "" #: board_photo_import.inx msgid "Remote camera" msgstr "" #: board_photo_import.inx msgid "Address of the remote machine (IP or IP:port):" msgstr "" #: board_photo_import.inx msgid "Machine running the capture server, for example 192.168.1.20" msgstr "" #: board_photo_import.inx msgid "Port:" msgstr "" #: board_photo_import.inx msgid "Picture:" msgstr "" #: board_photo_import.inx msgid "Take a new photo (/capture)" msgstr "" #: board_photo_import.inx msgid "Use the last photo taken (/old)" msgstr "" #: board_photo_import.inx msgid "Timeout (s):" msgstr "" #: board_photo_import.inx msgid "Resolution of the calibrated photo (px/mm):" msgstr "" #: board_photo_import.inx msgid "4 px/mm = 0.25 mm per pixel; higher values make a heavier document" msgstr "" #: board_photo_import.inx msgid "JPEG quality:" msgstr "" #: board_photo_import.inx msgid "Board detection" msgstr "" #: board_photo_import.inx msgid "Vectorize the board outline and holes" msgstr "" #: board_photo_import.inx msgid "Board tone:" msgstr "" #: board_photo_import.inx msgid "Lighter than the bed (light wood on honeycomb)" msgstr "" #: board_photo_import.inx msgid "Darker than the bed (dark board on light surface)" msgstr "" #: board_photo_import.inx msgid "Threshold (0 = automatic):" msgstr "" #: board_photo_import.inx msgid "Grey level between board and bed; 0 computes it automatically (Otsu)" msgstr "" #: board_photo_import.inx msgid "Smoothing (mm):" msgstr "" #: board_photo_import.inx msgid "Removes specks and fills small notches smaller than about twice this value" msgstr "" #: board_photo_import.inx msgid "Minimum hole area (mm²):" msgstr "" #: board_photo_import.inx msgid "Smaller holes are ignored (filled)" msgstr "" #: board_photo_import.inx msgid "Outline tolerance (mm):" msgstr "" #: board_photo_import.inx msgid "Maximum deviation allowed when simplifying the outline" msgstr "" #: board_photo_import.inx msgid "Outline colour:" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Diagram" msgstr "" #: board_photo_import.inx board_photo_markers.inx msgid "Help" msgstr "" #: board_photo_import.inx msgid "" "1. Print the 4 markers (Board photo: print\n" " calibration markers, A4 sheet) and stick\n" " them at the corners of the honeycomb.\n" "2. Lay the board on the bed and take a photo\n" " from above showing the 4 markers.\n" "3. With nothing selected, choose the photo\n" " file, or the address of the remote camera\n" " (capture server), and apply: the photo is\n" " straightened and\n" " placed at the exact scale of the work area,\n" " with the board outline and holes.\n" "4. Draw or place the shapes in the \"Cuts\"\n" " layer, on the board, then export them with\n" " \"Export to LaserGRBL\".\n" "\n" "If the markers are not found, the raw photo\n" "is placed with 4 red targets: move them onto\n" "the marker centres, select the layer content\n" "(Ctrl+A) and apply again.\n" "\n" "Markers around the honeycomb (default): stick\n" "the 4 printed pieces so that the inner corner\n" "of each piece touches a corner of the\n" "honeycomb, the two-dot marker at the bottom\n" "left. The bottom left corner of the honeycomb\n" "is then the laser origin, i.e. the bottom left\n" "of the page, as expected by the export to\n" "LaserGRBL.\n" "\n" "Coordinates are in mm from the laser origin\n" "(bottom left of the work area)." msgstr "" #: board_photo_markers.inx msgid "Board photo: print calibration markers" msgstr "" #: board_photo_markers.inx msgid "Output:" msgstr "" #: board_photo_markers.inx msgid "Markers to engrave on the bed" msgstr "" #: board_photo_markers.inx msgid "A4 sheet to print (markers to cut out)" msgstr "" #: board_photo_markers.inx msgid "Placement guides to engrave on the bed (for printed markers)" msgstr "" #: board_photo_markers.inx msgid "Laser work area (mm)" msgstr "" #: board_photo_markers.inx msgid "Calibration markers, inside or around the work area (laser origin at the bottom left)" msgstr "" #: board_photo_markers.inx msgid "Printed sheet" msgstr "" #: board_photo_markers.inx msgid "" "Print the sheet at actual size (100 %,\n" "no \"fit to page\"), preferably from a PDF\n" "(File > Save a Copy > PDF). Then measure\n" "both 100 mm bars.\n" "\n" "Only if the printer still shrinks the sheet,\n" "enter the measured lengths below: the sheet\n" "is enlarged to compensate. Print it again\n" "and check that the bars now measure 100 mm." msgstr "" #: board_photo_markers.inx msgid "Measured length of the horizontal bar (mm):" msgstr "" #: board_photo_markers.inx msgid "Measured length of the vertical bar (mm):" msgstr "" #: board_photo_markers.inx msgid "" "Engraved markers: engrave them once, filled,\n" "on light plates fixed to the bed, keeping a\n" "light area of twice the marker size around\n" "each one.\n" "\n" "Printed markers:\n" "1. \"A4 sheet\": print at 100 % (no fit to\n" " page), check the 100 mm bar, cut out the\n" " 4 pieces along the dashed lines.\n" "2. \"Placement guides\": engrave them lightly\n" " on the bed (thin red lines).\n" "3. Stick each piece inside its guide, the\n" " ticks of the piece on the cross.\n" "\n" "The markers must stay in place: every photo\n" "is scaled from them. The marker with two dots\n" "is the origin marker, at the bottom left\n" "(laser origin). Use the same settings in\n" "\"Board photo: import and calibrate\"." msgstr "" #: board_photo_import.py board_photo_markers.py msgid "Work area, marker spacing and marker size must be strictly positive." msgstr "" #: board_photo_import.py msgid "Choose the photo of the board in the \"Photo\" tab (or select a photo and 4 markers for a manual calibration)." msgstr "" #: board_photo_import.py msgid "Photo not found: {}" msgstr "" #: board_photo_import.py msgid "This file cannot be read as an image: {}" msgstr "" #: board_photo_import.py msgid "Enter the address of the remote machine in the \"Photo\" tab (for example 192.168.1.20)." msgstr "" #: board_photo_import.py msgid "Invalid remote address: {}" msgstr "" #: board_photo_import.py msgid "The remote machine cannot be reached ({}): check its address, that the capture server is running and that the port is open." msgstr "" #: board_photo_import.py msgid "The remote machine did not answer in time ({}): increase the timeout or check the network." msgstr "" #: board_photo_import.py msgid "The transfer of the photo was interrupted ({}), even after a second attempt: check the network and try again." msgstr "" #: board_photo_import.py msgid "The capture server returned an error: {}" msgstr "" #: board_photo_import.py msgid "The capture server did not return an image: {}" msgstr "" #: board_photo_import.py msgid "The image returned by the capture server is too large ({})." msgstr "" #: board_photo_import.py msgid "Remote capture failed: {}" msgstr "" #: board_photo_import.py msgid "The capture server did not return a readable image ({})." msgstr "" #: board_photo_import.py msgid "Photo received from {} ({} x {} px)." msgstr "" #: board_photo_import.py msgid "Manual calibration: select the photo and exactly 4 small shapes centred on the markers (for example Ctrl+A in the \"Manual calibration\" layer). Deselect everything to import a new photo." msgstr "" #: board_photo_import.py msgid "The selected image cannot be read (embed it, or check that the linked file still exists)." msgstr "" #: board_photo_import.py msgid "The selected image has no size." msgstr "" #: board_photo_import.py msgid "Manual calibration" msgstr "" #: board_photo_import.py msgid "Marker target" msgstr "" #: board_photo_import.py msgid "no dark shape found" msgstr "" #: board_photo_import.py msgid "{} marker(s) found out of 4" msgstr "" #: board_photo_import.py msgid "the markers found do not form a rectangle" msgstr "" #: board_photo_import.py msgid "Automatic marker detection failed ({})." msgstr "" #: board_photo_import.py msgid "The raw photo was placed in the \"Manual calibration\" layer with 4 red targets: move each target onto the centre of a marker (zoom in), select the layer content (Ctrl+A) and run this extension again." msgstr "" #: board_photo_import.py msgid "The 4 marker positions do not form a convex quadrilateral: check them and try again." msgstr "" #: board_photo_import.py msgid "The 4 marker positions are aligned: check them and try again." msgstr "" #: board_photo_import.py msgid "The origin marker (two dots) was not recognised: the photo is assumed upright (origin at the bottom left of the photo)." msgstr "" #: board_photo_import.py msgid "A marker measures {:.1f} mm instead of {:.1f} mm: check the marker positions and size in the \"Work area\" tab." msgstr "" #: board_photo_import.py msgid "No board found on the photo: try the other \"Board tone\" or set the threshold by hand." msgstr "" #: board_photo_import.py msgid "The page is not the size of the work area: the export to LaserGRBL takes the bottom left of the page as the laser origin, so tick \"Set the page to the work area size\" before cutting." msgstr "" #: board_photo_import.py msgid "Board photo calibrated: {:.2f} mm per photo pixel." msgstr "" #: board_photo_import.py msgid "{} hole(s) found." msgstr "" #: board_photo_import.py msgid "Board photo" msgstr "" #: board_photo_import.py msgid "Calibrated photo" msgstr "" #: board_photo_import.py msgid "Board outline" msgstr "" #: board_photo_import.py msgid "Board outline ({} holes)" msgstr "" #: board_photo_import.py msgid "Cuts" msgstr "" #: board_photo_markers.py msgid "The placement guides do not fit in the work area: keep every marker centre at least {:g} mm from the edges (1.5 x the marker size)." msgstr "" #: board_photo_markers.py msgid "The markers do not fit in the work area, so the laser cannot engrave them: reduce the spacing or move the origin marker. Markers placed around the work area (negative origin, larger spacing) are printed instead (\"Output\": A4 sheet) and stuck in place by hand." msgstr "" #: board_photo_markers.py msgid "The markers are too close to each other: the spacing must be at least twice the marker size." msgstr "" #: board_photo_markers.py msgid "Origin marker" msgstr "" #: board_photo_markers.py msgid "Marker" msgstr "" #: board_photo_markers.py msgid "Marker placement guides" msgstr "" #: board_photo_markers.py msgid "These markers are too large for an A4 sheet: reduce the marker size, or engrave them directly on the bed." msgstr "" #: board_photo_markers.py msgid "The measured bar lengths must be between 80 and 120 mm." msgstr "" #: board_photo_markers.py msgid "Calibration markers (print)" msgstr "" #: board_photo_markers.py msgid "Calibration markers - print at 100 %" msgstr "" #: board_photo_markers.py msgid "Print at actual size (no \"fit to page\"), then check that both bars measure 100 mm." msgstr "" #: board_photo_markers.py msgid "Cut along the dashed lines and stick each piece outside a corner of the honeycomb, its inner corner on that corner." msgstr "" #: board_photo_markers.py msgid "Marker size: {:g} mm" msgstr "" #: board_photo_markers.py msgid "printer correction: X {:.1f} %, Y {:.1f} %" msgstr "" #: board_photo_markers.py msgid "Top left" msgstr "" #: board_photo_markers.py msgid "Top right" msgstr "" #: board_photo_markers.py msgid "Bottom right" msgstr "" #: board_photo_markers.py msgid "Origin - bottom left" msgstr "" #: board_photo_markers.py msgid "Cutting line" msgstr "" #: board_photo_markers.py msgid "Alignment ticks" msgstr "" #: board_photo_markers.py msgid "Scale bar X" msgstr "" #: board_photo_markers.py msgid "100 mm (X)" msgstr "" #: board_photo_markers.py msgid "Scale bar Y" msgstr "" #: board_photo_markers.py msgid "100 mm (Y)" msgstr ""